Old Tank Removal
We shut off the water and gas or power, drain the old tank with a water heater drain pump, and disconnect the lines. The failed unit is hauled off-site for disposal, so you do not need to arrange a separate pickup.
Fast, code-correct service for apartments, duplexes, and small commercial properties
Water Heater Replacement for Multi-Unit Buildings in Carrollton
When your Carrollton multi-unit property loses hot water, every tenant calls at once. We handle Water Heater Replacement for Multi-Unit Buildings in Carrollton with same-day response, pulling permits and swapping tanks in one visit. From Downtown Carrollton to Castle Hills, our licensed plumbers work on gas, electric, and tankless systems. We install Rheem, A. O. Smith, and Bradford White units sized for your building's real demand.
Careful work. Honest options.
About this service
Water Heater Replacement for Multi-Unit Buildings in Carrollton
Water Heater Replacement for Multi-Unit Buildings in Carrollton is the licensed removal and installation of shared or individual water heating systems in apartment buildings, duplexes, triplexes, and small commercial properties. It covers isolating the old unit, draining the tank, checking gas or electrical connections, and setting a new heater that meets Uniform Plumbing Code and NFPA 54 requirements. We size each replacement to the building's actual fixture count, not a guess.
Carrollton's older rental stock around Old Downtown Carrollton and the Belt Line often runs 40-gallon tanks past their service life. Sediment buildup from hard water and corroded anode rods turn a working heater into a leaking tank. If you own a multi-unit building and need water heater installation for multi-unit buildings Carrollton Georgia, we handle the whole job, including removal and disposal of the old unit.
- ✓ Same-Day Tenant Relief
- ✓ Code-Correct Installs
- ✓ Right-Sized Equipment
- ✓ One Point of Contact
What's included
What Our Multi-Unit Replacement Includes
Every multi-unit replacement we quote covers the full job, not just the tank. You get the permit, the labor, the new fittings, and the disposal. Here is what is included in a standard replacement. Add-ons like tankless conversions or gas line upgrades are quoted separately before we start.
New Tank and Fittings
Your new Rheem, A. O. Smith, or Bradford White tank comes with fresh dielectric unions, flexible connectors, Teflon tape, and pipe dope. We do not reuse old fittings that could leak within a year.
Code Compliance Check
We verify the T&P valve, expansion tank, venting, and gas connections against the Uniform Plumbing Code and NFPA 54. If the old install was missing a drip leg or a proper vent, we correct it as part of the job.
Permit and Inspection
We pull the required Carroll County permit and schedule the inspection. You get the paperwork for your records. This keeps your rental license and certificate of occupancy in good standing.
Testing and Walkthrough
We fire the burner or energize the element, check for gas leaks, confirm hot water at the farthest fixture, and walk you through the new unit. You know where the shutoff is and how to read the T&P valve.
How it works
How Our Replacement Process Works
Call (943) 469-0029 and we ask the right questions: how many units, gas or electric, tank age, and whether you have active leaks. We quote a realistic range on the call and book a site visit if the building needs a load calculation.
We measure the mechanical space, count fixtures, and check gas line size or breaker capacity. For tankless conversions we verify venting. This takes 30 to 45 minutes and prevents the wrong tank showing up on install day.
We pull the required Carroll County permits and coordinate a work window with you and your tenants. Most jobs are scheduled within 24 to 72 hours. Emergency calls get priority and can be same-day.
We shut off gas or power, drain the old tank with a water heater drain pump, and disconnect the lines. New brass fittings, Teflon tape, and pipe dope go on, then the new unit is set, connected, and filled. Expect 3 to 5 hours per unit.
We fire the burner or energize the element, check for gas leaks with a multimeter and soap test, verify the T&P valve and expansion tank, and confirm hot water at the farthest fixture. You get a walkthrough and the old tank hauled away.
STEP 01Phone Assessment
Call (943) 469-0029 and we ask the right questions: how many units, gas or electric, tank age, and whether you have active leaks. We quote a realistic range on the call and book a site visit if the building needs a load calculation.
Tools & methods
Tools and Methods We Use
Water heater drain pump
Moves water from the old tank to a drain or outside without spilling it across the floor. Essential in upstairs mechanical closets where a gravity drain is not available.
Pipe wrench and tube cutter
Used to break loose old unions and cut copper or PEX tubing cleanly. A clean cut means a better fit and fewer leaks on the new connections.
Soldering torch and flaring tool
For copper repairs and gas line work. We solder copper joints where required and use a flaring tool for gas flex connections that need a flare fitting.
Multimeter and T&P valve tester
The multimeter checks heating elements, thermostats, and power at the unit. The T&P valve tester confirms the relief valve opens at the correct pressure.
Expansion tank and dielectric unions
An expansion tank absorbs pressure changes on a closed system. Dielectric unions stop electrolysis between copper and steel, which extends the life of the tank connections.
Flexible connectors and gas flex connector
Allow a clean connection between the tank and the building's piping. We replace them on every job rather than reusing old ones that may be corroded.
Real results
Before and after.
Water Heater Replacement for Multi-Unit Buildings
Fourplex in Old Downtown Carrollton
Two 40-gallon tanks were leaking and the mechanical closet had standing water. Tenants in two units had no hot water, and the owner was getting daily calls.
After: We replaced both tanks with 50-gallon Rheem units, installed new expansion tanks, and piped the T&P valves to a safe drain. Both units had hot water by 4 p.m. the same day.
Book this service →
Water Heater Replacement for Multi-Unit Buildings
18-Unit Building in Trinity Mills
A 75-gallon commercial tank was rusting and could not keep up with morning demand. Tenants on the top floor complained about lukewarm water.
After: We installed a high-recovery commercial tank and balanced the recirculation line. The building now holds 120 F at the farthest fixture, and gas use dropped compared to the old unit.
Book this service →
Water Heater Replacement for Multi-Unit Buildings
Duplex in West Carrollton
One electric tank was leaking onto the garage floor, and the other was making popping noises from sediment buildup. The owner wanted both replaced before winter.
After: We swapped both units for 40-gallon electric tanks with new dielectric unions and thermostats. The garage floor was dry, and both tenants had hot water the same afternoon.
Book this service → Problems we solve
Multi-Unit Water Heater Problems We Solve
Multi-unit water heaters fail differently than single-family units. Higher demand, shared walls, and hard water wear them out faster. Here are the problems we fix most often for Carrollton property owners.
Ask a pro →Leaking tank flooding a mechanical closet
We shut off the supply, drain the tank, and install a new unit the same day. We check the floor drain and pan, and we make sure the T&P valve discharge is piped correctly so the next failure does not flood the closet.
No hot water in multiple units at once
We diagnose the cause first. If the tank is dead, we replace it. If it is a heating element or thermostat, we repair it. For multi-unit buildings, we can install a correctly sized commercial tank or a tankless bank to handle peak demand.
Rusty water and popping noises
We replace the corroded tank, flush the lines, and install a new anode rod. For Carrollton's hard water, we recommend an annual flush to keep the new unit running longer.
Failed T&P valve or expansion tank
We test the T&P valve with a T&P valve tester, replace it if it fails, and install a correctly sized expansion tank. We check system pressure and confirm the discharge line is safe.
Transparent pricing
Multi-Unit Water Heater Replacement Pricing
$850 - $2,400 per unit depending on tank size, fuel type, and access
Typical 2026 pricing for multi-unit replacement in Carrollton runs $850 to $1,800 per tank for a standard swap, and $1,200 to $2,400 per unit for larger commercial or tankless work. The final number depends on tank size, gas versus electric, access, and whether the old install needs code corrections. We quote the full job, including removal and disposal, before we start. For property managers with several buildings, we offer per-unit pricing that drops when you replace multiple tanks in one visit.
The price covers the permit, removal, disposal, new fittings, and testing. You get one invoice and a written warranty. Planned replacement costs less than an emergency flood repair and keeps your tenants in hot water.
•affects cost
A 40-gallon electric tank costs less than a 75-gallon commercial gas unit. Tankless and hybrid units cost more upfront but can lower utility bills over time.
Get a quote ↗•affects cost
Gas units need venting, a gas flex connector, and a combustion air check. Electric units are simpler but may need a breaker or wire upgrade if the new tank draws more power.
Get a quote ↗•affects cost
A tank in a basement or tight mechanical closet takes longer to remove and install. Upstairs units need a drain pump and extra labor to protect the floors below.
Get a quote ↗•affects cost
If the old install is missing a drip leg, a proper T&P discharge, or an expansion tank, we correct it during the replacement. Those fixes add parts and labor but keep you inspection-ready.
Get a quote ↗ Proof you can check
Licensed, Insured, and Warrantied
- Georgia Plumbing License · Georgia State Board of Plumbing
- Manufacturer certification (Rheem, A. O. Smith, Navien) · Manufacturer training programs
- Uniform Plumbing Code (UPC) compliance · International Association of Plumbing and Mechanical Officials
- NFPA 54 (National Fuel Gas Code) compliance · National Fire Protection Association
- OSHA safety compliance · Occupational Safety and Health Administration
Customer reviews
What Carrollton Property Owners Say
★★★★★
“I own a fourplex near Old Downtown Carrollton and two tanks failed the same week. They came out, quoted the job, and had both Rheem units running by 4 p.m. Tenants stopped calling. The invoice matched the quote, and they hauled the old tanks away.”
MT
Marcus T.Property Owner, Old Downtown Carrollton
✓ Verified“
★★★★★
“We manage 18 units in Trinity Mills and had a 75-gallon commercial tank leaking on a Friday. They answered the phone, arrived in about two hours, and had the new unit installed that evening. The mechanical room was dry and clean when they left.”
DR
Denise R.Property Manager, Trinity Mills
✓ Verified★★★★★
“I had a duplex in Hebron with rusty water and a popping tank. They diagnosed a corroded anode rod and sediment buildup, then replaced the 50-gallon unit with a Bradford White. Hot water was back the same day, and they registered the warranty for me.”
AK
Alan K.Landlord, Hebron
✓ VerifiedMost single-unit replacements run $850 to $1,800 per tank, and multi-unit jobs often land between $1,200 and $2,400 per unit depending on tank size, gas versus electric, and access. A 75-gallon commercial tank or a tankless conversion costs more. We quote the full job, including removal and disposal, before we start.
We do. Carrollton Water Heater Replacement Pros handles apartment buildings, duplexes, and small commercial properties across Carroll County. We are licensed, insured, and carry Rheem, A. O. Smith, and Bradford White units on the truck. Call (943) 469-0029 and we will confirm availability for your address.
Plan on 3 to 5 hours per unit for a standard tank swap. A tankless conversion or a commercial 75-gallon install can take 6 to 8 hours. If we are replacing several tanks in one building, we stagger the work so some units keep hot water while we work.
Yes. We run 24/7 emergency service for leaking tanks, no hot water, and gas or electrical faults. Call (943) 469-0029 and we will dispatch a licensed plumber. Most emergency multi-unit replacements are completed the same day, including removal of the failed tank.
Ready when you are
Get Water Heater Replacement for Multi-Unit Buildings in Carrollton
One call covers the whole job: permit, removal, new tank, and cleanup. We are licensed, insured, and we answer the phone 24/7. Call (943) 469-0029 and we will schedule your multi-unit replacement today.
Call Now (943) 469-0029 →
Request an appointment
Call for Water Heater Help
Reach us at (943) 469-0029 any time, day or night. We answer live, ask a few questions about your tank, and get a plumber headed your way. Regular appointments run Monday through Friday, and emergency calls are covered 24/7 across Carrollton and Carroll County.
Call anytime(943) 469-0029Email the officeinfo@waterheaterreplacementcarrolltonga.xyz
Office hoursOpen 24 hours · 7 days a week